Tenergy Smart Universal Charger for NiMH / NiCd Battery pack 7.2V - 12V with charging current Selection/Temperature Sensor Details
Product Description
Accessories Included
* 1 standard Tamiya Female connector and Fuse house with the smart battery charger.
* 1 connector adaptor from standard Male Tamiya to Mini Female.
* 1 set of clip adaptor with Male Tamiya connector on one end.
* 2 additional fuses
Smart Charger Specification
* FOR 6V-12V NI-MH/NI-CD BATTERY PACK 6-10PCS BATTERY
* Input: AC100-240V
* Output: 6-12V 0.9or1.8A
Operation Instruction
* Connect battery pack to output connector and plug AC power source.
* Make sure battery polarity is connected correctly (Red wire is positive)
* Charger will detect battery voltage automatically, Red LED will be on during charging
* When battery is fully charged, current will reduce to trickle charging at 50mA,Green LED will be on
* Battery will be charged at 0.9A or 1.8A constant current,
* Approximate Charging time is about 1.5hrs for 3000mAh battery,1hr for 1800mAh battery.
* The charger is designed for faster charging NiCd and NiMH battery packs from 6 to 12V for RC car/Air and Air soft gun.
* Don't charge battery packs with voltage less than 6V or voltage greater than 12V and capacity smaller than1100mAh.
* Battery pack must be made by high drain current cell.
* Please contact your seller for instruction. Mfg is not responsible for any damage and consequent damage by Misusage.
Caution
* The charger is designed for indoor use only. Don't leave the charger unattended during charging.
* The Charger should be positioned horizontally and work in well ventilated condition, avoid water and keep it away from flammable explosive goods.
* Don't cover the charger when charging, ambient temperature shall not be more than 40oC
* Don't touch the plug.
* Don't leave the abtteries and chargers on wood surface or carpet.
* Cut off the power supply before connect or disconnect the charger with batteries.
* Don't try to disassemble the charger, High voltage inside, danger!
- Best Charger for charging all RC Car, RC air and Airsoft battery packs 7.2V, 8.4V, 9.6V and 12V.
- Fast charger with current switch to select either, 0.9A and 1.8A. Deliver full charge within 1 - 2 hours.
- Worldwide usage with 120-240V AC.
- Use pulse and negative pulse technology to avoid battery overheating during fast charging, optimized for battery pack's cycle life.
- Safety protection fuse for over current, short circuit & reverse polarity protection
Where to buy Tenergy Smart Universal Charger for NiMH / NiCd Battery pack 7.2V - 12V with charging current Selection/Temperature Sensor
Tenergy Smart Universal Charger for NiMH / NiCd Battery pack 7.2V - 12V with charging current Selection/Temperature Sensor Reviews
| 12 of 12 people found the following review helpful  Charger, By Amazon Verified Purchase This review is from: Tenergy Smart Universal Charger for NiMH / NiCd Battery pack 7.2V - 12V with charging current Selection/Temperature Sensor (Electronics) Just got the charger today 2 days ahead of delivery date-- good job-- So far the charger works fine- charged a dead battery less than one and a half hours- did not heat up the battery 11 of 11 people found the following review helpful pure power for my rustler, Amazon Verified Purchase This review is from: Tenergy Smart Universal Charger for NiMH / NiCd Battery pack 7.2V - 12V with charging current Selection/Temperature Sensor (Electronics) i ordered the 2 tenergy 9.6v 4200mah hump back batteries for my rustler then also ordered this chargerit came early,works perfectly,pure brainless and it charges these packs in about three hours,i think...i let 1 pack charge over night,not on purpose,just foregot.no worries though the charger will not over charge the batteries. go ahead,don't be shy,proceed to the checkout!!! 6 of 6 people found the following review helpful  its a charger, By David Atkinson (LOS FRESNOS, TEXAS, US) - See all my reviews Amazon Verified Purchase This review is from: Tenergy Smart Universal Charger for NiMH / NiCd Battery pack 7.2V - 12V with charging current Selection/Temperature Sensor (Electronics) it works it does what it says it will donothing special charges 7.2v 8.4v 9.6v 10.8 battery's comes with a mini type connector and a large type connector uses a temperature sensor as a fail safe if it over heats ONLY CHARGE NiMH or NiCd battery's with this charger it blows up LiPo's charges battery's in about half an hour to an hour |
› See all 46 customer reviews...
No comments:
Post a Comment